Oriemac Machinery & Equipment (Shanghai) Co., Ltd. >> Lonking 8.5 Ton Small Excavator with Breaker Optional Cdm6085

Lonking 8.5 Ton Small Excavator with Breaker Optional Cdm6085

Lonking 8.5 Ton Small Excavator with Breaker Optional Cdm6085
Price: US $ 35000/Piece
Min Order: 1/Piece
Pay Type: L/C,T/T,D/P,Western Union,Paypal

Lonking 8.5 ton Small Excavator with Breaker Optional CDM6085
 

Construction Machinery CDM6085/6085E features:

 

CDM6085 is equipped with a lownoise, low emission, small size, and strong power YANMAR engine. It is also equipped with a pump load independent flow distribution control system (LUDV) unrelated to the load pressure. The machine has many characteristics,such as energy saving, full-featured , good stability , high productivity, spacious and comfortable cab etc.
CDM6085 is widely used formunicipal engineering, garden project, irrigation and water conservancy constructionetc.

Yanmar TNV series engine
The original Yanmar four-cylinder, four-stroke, water-cooled, direct injection engine. It's powerful and fuel-efficient. Using the unique CAE technology of Yanmar, large muffler, and a new type cooling fan, effectively reducing the noise and vibration of the machine. And the engine conforming to Euro IIIA emission standard is optional.
Filtering System
The high efficiency dual element air filter ensures the quality of engine air intake. In addition, the air pre-filter can carry out the rough filtration over the air intake to enable the operation under the poor air quality working conditions and prolong the maintenance interval of the air filter. The oil-water separator and t high- precision fuel filter will filtrate the fuel many times to ensure the quality of fuel fed to the engine.
Cooling System
The parallel radiator cooling makes cooling effect better and service easier.
Maintenance and Service
The easy maintenance of direct injection engine reduces the cost of maintenance.. This will enhance the service efficiency, relieve the customers of worry about the service and ensure the attendance rate of excavator.
Control Mode
New LUDV system is able to fine control the actions of each group of spool of multiple unit valve, and to distribute engine power as the largest proportion according to the system needs, so as to realize the best match under the variety of work conditions or working load, and resulting in the largest operation efficiency, as well as improve the operational stability and reliability of the excavator.
Functions
Fine control of the rotation speed (In the motion starts).
Flow and pressure control at the same time.
Effective control of the rotation speed (When associated with other motions).
Excellent acceleration and deceleration performance.
Auxiliary Hydraulic Valve
The main valve is provided with a set of standby valves to facilitate the installation of other accessories such as the breaking hammer. 
Filtering System
The hydraulic circuit is equipped with the high quality hydraulic oil filter which can prolong the service life of the hydraulic elements. 
Components Layout
The special design of hydraulic system and components location can enhance the system efficiency of the machine. Parts are arranged closely to shorten the connecting lines and consequently reduce the line friction and pressure drop.
Monitor
The large LCD display provides a convenient visual user interface. Operation parameters of the machine, such as engine speed, coolant temperature, engine oil pressure, fuel level, real-time and historical faults, may be displayed in the liquid crystal monitor.
Fault Auto Warning
Prompting the machine failure and automatic alarm through sound, light, and text.
Main frame
The reasonable layout of robust main frame optimizes the utilization of steels. 
Undercarriage
The X-shaped undercarriage with heavy-duty box structure is subjected to the repeated finite element analytical calculation and enhance the overall rigidity, strength and torsional resistance. Undercarriage is welded from the low alloy structural steel plates with overall process quality control. The critical welds are fully subjected to fault detection and stress test to ensure the product quality. 
Track
There are ribs and crawler cradle in the middle of the track links. Using m-type seals to ensure the lubricating effect of the pin and pin suites.Extending the track working life effectively.
Travel Device
The drive unit employs the imported motors of high quality and the drive wheel adopts high frequency heating overall hardening process to enable the excellent wear resistance of the external gear rim.
Idler Cushion
The idler cushion with high quality sealing elements effectively guarantee the high pressure sealing inside the cylinder block, the springs are subjected to the special heat treatment to allow the excellent fatigue resistance.
Cab Shock Absorption System
The cab shell is installed to the platform through the cushioning materials consisting of the silicon oil and rubber to relieve the vibration, reduce the noise and guarantee the operation comfort. 
Windows
The glass is clung to the cab directly without frame to enlarge the visual field. The windows allow free adjustment to open/close the front and upper window and windshield,besides, the front glass can be set to the roof above the operator. 
Front Wiper
The wiper located in front of cab pillar enlarges the operator's field of view, it allows the continuous and intermittent operation modes. 
Safe and Comfortable Cab
The spacious and multi-function cab designed according to ergonomics enhances comfort for operator. The reasonable layout of control elements inside the cab allows easy operation.
Standard Cab Equipment
The cab inside includes the cigar lighter, ash tray, cup holder, storage rack, coat hook , escape hammer, and fire extinguisher.
A/C System
The high performance and healthy A/C allows the air circulate. Concise control panel and easy press key operation, multi-direction A/C air outlet allowing fast regulation of cab inside temperature and fast defrosting.
Deluxe Seat
The comfortable suspension type seat is provided with a hydraulic damper, the wide seatback allows the waist support and the curve profile enables comfortable riding, the double slide track multi-way multi-step regulation enables different operators to find the best posture, the wide pedal space allows the free body stretching and relieves the operator from the long time operation fatigue. 
Safety Lock Joystick
The hydraulic safety lock joystick is located at the outside of center left armrest box in the cab. The machine control is active only when the joystick is in ON position, which can prevent the wrong operation in an effective way. 
Control Lever
The reasonable design of control lever saves the operating effort by the lever principle, the ergonomic design enables the operator to maintain the natural wrist and arm posture. The moderate joystick stroke relieves the degree of fatigue and ensures the accurate control. 
Switch Control Panel
The control panel on the left/right pilot box is in concise and esthetic layout and the operation of keystroke is easy.
Boom and Arm
To cope with high load during operation, the design & development team of LONKING adopts lots of up-to-date design ideas, preserves the higher safety factor, employs finite element analysis, calculation and optimum design to finish the development of boom and arm and selects the high strength low alloy structural steels for the boom and arm fabrication. 
Pin Shaft
The pin shaft is the core element for the connection of the working equipment. LONKING chooses the professional pin shaft suppliers and subject the pin shafts to the strict fault detection to ensure the quality. The pin shaft of LONKING excavators has thick chrome plating coat and high surface finish. The special treatment enables the extremely high wear resistance and corrosion resistance.
Bucket
The bucket body is made of low alloy and high tenacity materials and the external structure is made of high strength and wear-resistant steels, which constitute the entire reinforced bucket. Standard bucket with flat-floor which is praised by users is more suitable for the formation conditions. This excavator provides different bucket options to meet different working demands.
Easy Maintenance and Service
The design and layout of CDM6085 consider to providing convenience for maintenance personnel. Most maintenance locations can be accessed from the ground level to enable the fast and high efficiency maintenance. The maintenance points are clearly identified, easy to operate. The electrical elements are near the outside of machine to facilitate the maintenance. 
Long Maintenance and Service Cycle
The maintenance and service cycle of CDM6085 has been prolonged to reduce the maintenance parts collection and enhance the availability.


Specifications:

 

SpecificationsCDM6085CDM6085E
EngineModelYanmar 4TNV98T (Stage II)Yanmar 4TNV98T(Stage IIIA)
Rated power57.7 kW (78.5 hp) /2200 rpm56.5 kW (76.8 hp) /2200 rpm
Bore × Stroke98mm×110mm98mm×110mm
Displacement 3.319 L3.319 L
Min. Fuel Consumption244 g/kw.h
CommentMaintain the rated power at 2300m elevation.
Operating weightSummaryOperating weight:8600 kg
The operating weight includes the weight of 3720 mm standard boom, 1665 mm standard arm,
 0.36m3 standard bucket, 450 mm track shoes, lubricating oil, coolant, 
the full diesel oil tank and the rest standard configuration units.
Ground pressure37 kPa
Fluid capacityFuel tank146 L
Hydraulic oil tank120 L
Cooling system19 L
Engine oil12 L
Swing drive unit2 L
Traveling gear 2×1.4 L
Swing motorSummaryPlunger Type (with safety  valve and closed type brake)
Swing speed 11.69 rpm
Travel motorSummaryPlunger Type (with safety  valve and closed type brake)
Taveling speed2.8 -4.5 km/h
Gradeability35°(70%)
Maximum Traction75.2 kN
Traveling mechanismStandard track shoe width450 mm
No. of track shoe38 (each side)
No. of carrier rollers1 (each side)
No. of track rollers5 (each side)
Hydraulic systemMain pumpAxial variable plunger pump
Max. flow of system74.8×2 L/min165 L/min
Max.pressure 28.5 MPa
Max. pilot pressure3.7 MPa
Operating equipmentEach machine action is under the pilot control. The right lever controls the motion of boom 
and bucket while the left lever controls the arm motion and upper structure swing. 
The foot pilot valve is provided with the lever joystick to control the machine traveling or
 turning by the foot or lever. The traveling gear shift adopts the solenoid switch control. 
Electrical systemSystem voltage: 24 V
Battery:12 V, 100 A
Boom Length (mm)3720
Arm Length (mm)1665
a Transport length (mm)6186
b Total transport height (mm)2743
c Tumblers distance (mm)2130
d Tail slewing radius (mm)1804
e Counterweight ground clearance (mm)803
f Track gauge (mm)1750
g Total transport width (mm)2200
h Upper structure width (mm)2160
i Standard track shoe width (mm)450
J Min. ground clearance (mm)356
Cab height(mm)2743
Boom Length (mm)3720
Arm Length (mm)1665
A   Max. digging radius (mm)6388
B Max. digging depth (mm)4140
C Max. digging height (mm)7123
D Max. dumping height (mm)5119
E Max. digging radius on ground (mm)6245
F Dozer height (mm)395
Max. bucket breakout force-ISO (kN)64.1
Max. arm breakout force-ISO (kN)43.5

Transport Size
The following sizes approximate to that of the equipment of standard configuration.

 


Prod Model: Excavator
Color: Yellow
Operating Weight: 8050 Kg
Rated Power: 57.7 Kw
Max. Digging Height: 7123 mm
Max. Dumping Height: 5119 mm
Max. Digging Depth: 4140 mm
Max. Digging Reach: 6388 mm
Min. Swing Radius: 1705 mm
Engine: Diesel Engine
Gradeability: 35%
Type: Crawler Excavator
Size: Small-Scale
Certification: ISO9001: 2000
Condition: New
Oriemac Machinery & Equipment (Shanghai) Co., Ltd. is a top package equipment solution provider in Shanghai, China, especially for construction machinery, heavy industrial equipment and vehicle. We are always committed to offer our customers high quality products with reliable performance, competitive price and comprehensive services, to ensure every engineering project to be run smoothly and on schedule. With over 8 years experience in the field of engineering industry and accompanying to fulfill strictly ISO 9001: 2008 standard, Oriemac had established and have been consistently keeping good business relationship with many general contractors, civil engineering companies and construction companies throughout the world. We participated as package equipment provider previously include airport projects in Africa, power plant projects in Middle East, dredging projects in South America, highway projects in Oceania, rural and municipal road projects in Southeast Asia, and we are still achieving more and more projects at present.

To provide reliable products with quick delivery time, to make prompt reaction for spare parts and after-sales services, to visit the users field regularly for local training and maintenance, Oriemac has been often praised by our customers and has taken great reputation as a trustworthy partner.

Oriemac believe in combining our own achievement together with our customer benefits. Open communication, effective planning and elaborative preparation always commit us to execute and deliver our promises for our customers.

Oriemac, industrial powers for your projects!

Send your message to this manufacturer

  • Oriemac Machinery & Equipment (Shanghai) Co., Ltd.

More >

Other Products with This Manufacturers